PTI_Product_Catalog

TECHNICAL INFORMATION

Avoid Common Engine Heater Installation Mistakes: TECHNICAL INFORMATION HEATERS A 50/50 mixture is recommended. Using a mixture that is richer than 65% will cause the element to fail prematurely. Do not run your engine while the engine heater is plugged in. This will create an air bubble around the element which will then cause the element to burn out prematurely. Do not plug in your engine heater prior to installing to ”see if it works”. Without being submerged in liquid, the heat generated has nowhere to go and could result in serious burns. How to safely test a heater. Connect a multi-meter to the heater pins. A reading between 5 ohms and 100 ohms indicates that the heater is working correctly. Do not use an engine heater when using 100% antifreeze.

RECOMMENDED PART APPLICATION BASED ON CLIMATE & EQUIPMENT Use the chart below to determine the recommended part based on the climate, starting system and equipment classification. 1. Select the appropriate "Temp” the equipment will operate under 2. Select the proper "Starting System” 3. Determine what "Engine Class” the equipment is classified 4. If you need additional information, please contact your Phillips & Temro Industries sales representative or contact customer service directly.

Do not use petroleum based lubricants on the O-ring. A petroleum based lubricant will significantly reduce the life of the O-ring. Use antifreeze instead. Do not over tighten the heater. The O-ring will form an adequate seal when the heater is torqued to the specifications in the instructions. Over tightening will strip the screw threads and reduce the quality of the seal. After heater use, disconnect the extension cord from the heater cord by firmly grasping each plug and pulling in opposite directions. Only grasp the plugs. Do not grasp, pull, yank or snap the cords to disconnect power. Damage will result to the power cord connections which could result in permanent malfunction and even an electrical short.

ATTENTION: 90% of maximum temperature will be reached in 5 hours of operation but the heater is designed for continuous overnight use.

Engine Class

TEMP °F/°C

Starting System

Heavy Duty Diesels to approx. 1150 CID (18.8 liters) 1500 Watt Immer sion, 1500 Watt Circulation Heater

Large Duty Diesels Industrial/Off Highway 2500 Watt Tank, 2250-2500 Watt Circulation Heater

Small Diesels 150 to 350 CID (2.4 to 5.7 liters) 400 to 750 Watt Immersion, 1000 Watt Circulation Heater 150 Watt Immersion with Thermostat Measured Shot Ether Kit, Battery Heater 600 or 750 Watt Immersion, 1000 Watt Circulation Heater 150 Watt Immersion with Thermostat Measured Shot Ether Kit, Battery Heater

Medium Duty Diesels to approx. 550 CID (9.0 liters) 750 or 1000 Watt Immersion, 1500 Watt Circulation Heater

Coolant Heater

40/4

Oil Pan Heater

300 Watt Immersion

150 Watt Immersion or 300 Watt Clamp-On

300 Watt Immersion or 500 Watt Clamp-On

Measured Shot Ether Kit, Battery Heater

Measured Shot Ether Kit, Battery Heater

Measured Shot Ether Kit, Battery Heater

Additional Products

DETERMINING CURRENT USAGE

0/-18

The current usage of a heater can be determined based on a heaters volt and wattage rating.

Coolant Heater

2500 Watt Tank, 2250-3500 Watt Circulation Heater

1500 Watt Immersion,

1000 Watt Immersion,

0/-18

Watts

Amperes @ 120 Volts

Amperes @ 240 Volts

Cost per hour *

2000 Watt Tank, 2000-2250 Watt Circulation Heater 300 Watt Immersion or 500 Watt Clamp-On

2250-2700 Watt Circulation Heater

75

0.63

0.31

.008

100

0.83

0.42

.010

150 200

1.25 1.67

0.63 0.84

.015 .020

Oil Pan Heater

150 Watt Immersion or 300 Watt Clamp-On

450 Watt Immersion

300

2.50

1.25

.030

Additional Products

Measured Shot Ether Kit, Battery Heater

Measured Shot Ether Kit, Battery Heater

Measured Shot Ether Kit, Battery Heater

450 500 750 850

3.75 4.17 6.25 7.08 8.33

1.88 2.08 3.12 3.54 4.16 6.25 8.34

.045 .050 .075 .085 .100 .150 .200 .250

-30/-34

Coolant Heater

750 Watt Immersion, 1500 Watt Circulation Heater

1500 Watt Immersion,

2000 Watt Immersion,

(2) 2500 Watt Circulation,

-30/-34

1000 1500 2000 2500

2250-2700 Watt Circulation Heater

2500-3500 Watt Circulation Heater

(2) 2500-3500 Watt Circulation Heaters

12.50 16.67 20.83

10.42

*Based on 10� per KWH

150 Watt Immersion with Thermostat Measured Shot Ether Kit, Battery Heater

450 Watt Immersion

450 Watt Immersion

Oil Pan Heater

300 Watt Immersion or 500 Watt Clamp-On Measured Shot Ether Kit, Battery Heater

Measured Shot Ether Kit, Battery Heater

Measured Shot Ether Kit, Battery Heater

Additional Products

-60/-51

phillipsandtemro.com

phillipsandtemro.com

164

165

Made with FlippingBook Digital Proposal Maker